suitpin8

Peugeot 208 Key Replacement Peugeot 208 key replacement should be left to experienced auto locksmiths who have the right equipment and technical knowledge. They can design and program keys more quickly and at a lower cost than dealerships. A dead coin battery is most likely to be the cause the reason your key-fob stops locking or unlocking doors. There are other reasons the key could be malfunctioning. Dead Coin Battery A dead coin battery can prevent your Peugeot 208 from locking or unlocking, and won't start the engine. If this is the case, you'll have to use the backup starting method that's described in the owner's manual of your vehicle. Another reason your 208 may not start is that the spark plugs have been damaged. The spark plugs light the fuel to start the engine. They have a limited life span. If they are not used enough and they fail, they'll eventually die. Luckily, there's an easy solution for this issue. The best thing to do is to test the voltage of your car battery using a multimeter. If it's below 11.5 volts then you must replace it. It is also necessary to clean the battery's contacts when it has corrosion. You can do this by lifting the rubber covers covering the two battery terminals and using wire brushes to clean any corroded areas of the battery. Then, you should connect the cables that connect the positive and negative poles. Water Damage If your 208 won't start and the battery hasn't failed, you should inspect the spark plugs. It could be that they are just overly dirty, which causes them not to spark. The spark plugs can be cleaned in an workshop. Peugeot cars are equipped with a transponder style key that integrates with the car's immobiliser system. This ensures that only a valid key is able to turn the engine. If the chip inside the Peugeot key is damaged, then it won't transmit the proper signal to the vehicle. This is a very common issue that is caused by water damage. This is especially prevalent in colder climates, as the vehicle may have been exposed to snow or rain. If this is the case, seek out a reputable auto locksmith who has all of the tools and equipment needed to modify the new key. They will also have all the latest technology and machinery required to make a Peugeot smart key. The process should take no more than 15 minutes. Faulty battery contacts Peugeot changed from the carbon-encased transponder chips and introduced a new type of chip that relies on electronic components within a circuit board. This new system works great when it's brand new, but over time the circuit boards start to deteriorate and stop working correctly. This could stop the immobiliser from working, so your vehicle will not start. Contact a Peugeot specialist, or a locksmith, if this is the situation. The most frequent issue is when the battery of the key fob begins to fail. This causes the blade of the key to stop feeding into the lock. A locksmith for cars will replace the battery, and then cut a fresh blade for you. This is a simple solution. Faulty Receiver Module If your Peugeot key fob stopped working after dropping it on the ground, being exposed to a sudden rain or accidentally washing it the wrong way, it could be due to a defective receiver module. The receiver is responsible for transmitting radio frequency signals to an on-board computer which controls the centralized locking system inside your Peugeot vehicle. The key fob itself is fitted with rubber seals to prevent water from reaching the chip inside. Water can damage the chip when it is exposed to water for a prolonged period of period of. The high salt content in the pool or ocean waters can cause damage to the key fob when it is submerged. If your Peugeot spare key fob isn't working then you'll have to get the module replaced. This can only be done by an expert auto locksmith or Peugeot specialist. Peugeot keys like other cars are secured by an immobilizer device. This requires the correct code to begin the car. This is why you should be able to trust a professional Peugeot locksmith to handle the task of creating and programming a replacement. Computers with faulty on-board computers The on-board computer in your Peugeot is the one responsible for all of the systems within your car, ranging from power windows to the airbags. The on-board computer will show an error code when something goes wrong. This code will be stored within the system until the issue is fixed. This will often require the on-board computers to be replaced. One of the most frequent reasons for the light coming on is loose or corroded connection in the airbag sensor. This can be caused by wear and tear, aging, or exposure to salt and moisture. This issue must be addressed as soon you can, because an airbag that is not functioning could pose danger in the event in the event of an accident. If your Peugeot is showing a card not detected error, the battery in the key fob could be dead or weak. This will stop the key fob from sending a signal that will disable the immobilizer in your vehicle. You can test this by pressing the unlock button on the key fob and then attempting to start your vehicle. If peugeot replacement key fails then the battery on the key is in need of replacement.